How to Install: 2022-2023 Tundra SS18 Stealth Bumper LED Light Bar Kit

SS18 Stealth Bumper LED Light Bar Kit
March 27, 2023 | Print this Page
How to Install: 2022-2023 Tundra SS18 Stealth Bumper LED Light Bar Kit

The SS18 Stealth Bumper LED Light Bar Kit for the 2022-2023 Toyota Tundra allows you to easily mount an 18" LED light bar in the factory lower bumper opening. The following installation guide will provide you with detailed instructions on how to install the SS18 Stealth Bumper LED Light Bar Kit for the 2022+ Toyota Tundra. Check out our Installation Video, or continue reading for step-by-step instructions below!

Note: This kit utilizes both factory and included hardware to mount the bracket to the vehicle.

Installation Tools

  • M10 Torque Wrench
  • M12 Torque Wrench
  • M6 Torque Wrench
  • 10mm Socket
  • 17mm Socket
  • Metric Wrenches
  • Ratchet/Extensions

Installation Video

 

Mounting Instructions

Step 1 -  Loosen Grille

Using a 10mm socket, remove the four bolts from the top of the grille.

10mm bolts on top of Tundra Grille

Step 2 - Disconnect Connectors

If equipped, disconnect the connectors from both corners of the grille as shown in the image below.

Tundra Connectors

Step 3 - Remove Wheel Well Screws

Using a 10mm socket, remove the four screws from inside the wheel well. If equipped with over-fender molding, remove the additional screw from the bottom inside of the wheel well opening. Repeat this step on the other side of the vehicle.

tundra wheel well screw locations

Step 4 - Remove Under Bumper Bolts

Remove the four 10mm bolts from underneath the bumper. If not equipped with a front spoiler, there will be four screws underneath the bumper that will need to be removed as well.

bolts below Tundra bumper

Step 5 - Remove Grille/Bumper Assembly

Pull out on both sides to release the clips holding the grille in place. Then remove the front grille/bumper assembly by pulling forward.

Removal of tundra grille

Step 6 - Remove Crash Bar Bolts

Using a 17mm socket, remove the two center bolts on the top side of the crash bar.

tundra crash bar bolts

Step 7 - Remove Bottom Crash Bar Bolts

Using a 14mm socket, remove the two center bolts on the bottom side of the crash bar.

Tundra Crash bar under bolts

Step 8 - Install Bracket

Install your new light bar bracket over the crash bar and secure it using the original bolts removed in the previous steps. Ensure the DD logo is in the correct orientation. Do not tighten the bolts. Repeat this step on the other side of the vehicle.

Tundra diode dynamics led light bar bracket

Step 9 - Install Light Bar

Attach the light bar to the brackets using the included M6 hardware, hand-tightening only.

Diode Dynamics LED Light Bar Tundra install

Step 10- Secure the Brackets

Once the light bar is mounted onto the brackets, tighten down the 17mm and 14mm bolts securing the brackets.

Bolting light bar bracket

Step 11- Connect Wiring Harness

Refer to the included heavy-duty light bar wiring harness guide to connect the light bar to the wiring harness.

connect LED Light Bar wiring harness

Step 12 - Unclip Wire Harness

Unclip the wire harness clips located below the lower grille opening shown in the pictures below.

tundra wire harness clips

Step 13 - Test Function

Test the function and aim the light bar as desired. If the light does not turn on, try flipping the connector 180°. Then, using a 10mm socket, tighten down the bolts.

Secure LED light bar

Step 14 - Reinstall Grille/Bumper Assembly

Reverse steps 1 through 5 to reinstall the grille/ bumper assembly onto the vehicle to complete the installation.

Tundra Grille Installation

Step 15 - Route Wiring Harness

Reroute the wire harness unclipped in step 12 to rest on top of the lightbar brackets.


Questions About the Installation?

If you have any questions or issues installing the SS18 Stealth Bumper Light Bar Kit for the 2022-2023 Toyota Tundra, please contact us for further assistance.

Where Can I Buy an SS18 Stealth Bumper Light Bar Kit for the 2022-2023 Toyota Tundra?

If you’re ready to upgrade your 2022-2023 Toyota Tundra with a Stealth Bumper Light Bar Kit, you can purchase one by clicking here or by using our dealer locator to find a dealer near you. 

If you are looking to add additional Off-Road LED Lights to your Tundra, we have a variety of LED Light bars and Pod Light kits here!

Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!

This Installation Guide is for the following SKUs: DD7411, DD7412, DD7413

Previous article:
Next article: